
Ceramic Cyclone Vortex Finder Liner
Ceramic Cyclone Vortex Finder Liners protect the internal bore of cyclone vortex finders from abrasive slurry, mineral particles, coal fines, ash and other solids. The liner is matched to the required bore, outer diameter, length and seating geometry to maintain the specified internal flow passage.
Product Structure
Alumina Ceramic Wear Layer
The internal wear surface uses alumina ceramic with grades from 92% to 99% Al₂O₃. Grade selection is based on particle abrasiveness, solids loading, temperature and chemical conditions.
Internal Bore
The finished bore follows the required internal diameter and length. Bore accuracy is important because the vortex finder forms part of the cyclone flow path.
External Fit
The outer diameter, seating area and locating features are matched to the supporting structure. Shoulder, stop and flange dimensions can be incorporated into the production drawing.
Key Product Benefits
Abrasion Protection: The alumina surface provides a hard wear barrier against continuous contact with abrasive particles moving through the vortex finder.
Bore Stability: Controlled ceramic thickness helps retain the specified internal bore during service and limits changes caused by surface wear.
Dimensional Matching: The liner can be produced from an approved drawing, dimensional record or existing component to suit the required installation geometry.
Localized Reinforcement: Ceramic thickness can be adjusted in defined wear zones where particle exposure is concentrated.
Reference Specifications
|
Parameter |
Reference Value |
|
Alumina Content |
92–99% Al₂O₃ |
|
Density |
3.6–3.9 g/cm³ |
|
Mohs Hardness |
Approx. 9 |
|
Porosity |
≤0.1% |
|
Bending Strength |
220–330 MPa |
|
Typical Wall Thickness |
5–25 mm |
|
Reference Service Temperature |
Up to 800°C |
|
Configuration |
Straight / Tapered / Custom |
Dimensional Selection
Internal Diameter
The bore diameter should be taken from the original component or approved drawing. This is a primary dimension for maintaining the intended flow passage.
Overall Length
The liner length should match the available installation depth, seating position and required coverage inside the vortex finder.
Wall Thickness
Thickness is selected according to the available space, wear exposure and supporting structure. The finished outside diameter must remain compatible with the installation interface.
Material Selection
92% Alumina: Used for general abrasive service where standard alumina wear protection meets the operating requirements.
95% Alumina: Selected where a higher alumina content and increased hardness are required for the operating conditions.
99% Alumina: Selected where higher-purity alumina is required for the specified service conditions.
Material selection should consider particle size, solids concentration, flow velocity, temperature and chemical environment.
Typical Applications
Mineral Processing
Used in cyclone systems handling abrasive mineral slurry during classification and separation
Coal Processing
Applied to cyclone components exposed to coal particles, mineral matter and circulating slurry.
Cement and Powder Processing
Used in solid-particle streams where continuous internal contact can create concentrated wear.
Chemical Processing
Applied where particulate streams require a ceramic wear surface combined with controlled internal geometry.
Wear Areas
Vortex Finder Bore: The internal bore is directly exposed to the moving material stream. Ceramic coverage and wall thickness are specified according to the expected wear pattern.
Entry Section: The upper section receives the process stream and may require additional ceramic coverage where particle exposure is concentrated.
Seating Interface: The seating area must match the supporting component to keep the liner correctly positioned during assembly and operation.
Manufacturing Control
Dimensional Inspection: Bore diameter, outer diameter, overall length and wall thickness are checked against the approved production drawing.
Surface Inspection: The ceramic surface is checked for visible cracks, edge damage and surface defects before shipment.
Fit Verification: Critical dimensions can be verified against supplied measurements or an existing component when replacement matching is required.
Replacement Information: For replacement work, the existing vortex finder drawing or dimensional record provides the main reference for production.
Existing Component: An existing liner or vortex finder can be measured for bore diameter, outer diameter, length and seating dimensions.
Measurement Record: When no drawing is available, record the internal diameter, external diameter, overall length, wall thickness and locating dimensions.
Installation Geometry: Shoulders, stop faces, flange positions and clearance areas should be included where they affect liner positioning.
Installation Considerations
Seating
The liner should be fully supported on the specified seating surface and positioned without creating an unwanted internal step.
Alignment
The ceramic bore should remain aligned with the surrounding component to maintain the required internal passage.
Joint Control
For sectional configurations, joint positions and internal transitions should follow the approved lining layout.
What to Specify for a Quotation
Provide the following information for technical review:
- Internal diameter
- External diameter
- Overall length
- Wall thickness
- Alumina grade
- Seating or flange dimensions
- Material handled
- Particle size
- Solids concentration
- Operating temperature
- Required quantity
A drawing, dimensional record or existing component can be used as the primary production reference.
FAQ
Q: What is a Ceramic Cyclone Vortex Finder Liner?
A: It is an alumina ceramic wear component installed inside a cyclone vortex finder to protect the internal bore from abrasive material.
Q: Which dimensions are required for selection?
A: The main dimensions are internal diameter, external diameter, overall length, wall thickness and seating or locating dimensions.
Q: Can the liner follow an existing vortex finder?
A: Yes. Production can be based on an approved drawing, measured dimensions or an existing component after dimensional review.
Q: Which alumina grade should be selected?
A: Common grades include 92%, 95% and 99% alumina. Selection depends on abrasive conditions, temperature, chemical environment and installation space.
Q: Can wall thickness be customized?
A: Yes. Wall thickness can be specified according to available installation space and the expected wear distribution.
Q: What information is needed for a quotation?
A: A drawing or dimensional record, material handled, particle characteristics, operating conditions, ceramic grade and required quantity provide the main technical information for quotation.
Hot Tags: ceramic cyclone vortex finder liner, China ceramic cyclone vortex finder liner manufacturers, suppliers, factory, ceramic liner
You Might Also Like
Send Inquiry









