
ZTA Ceramic Liner
A ZTA ceramic liner is not the same as an ordinary alumina tile. The difference is zirconia. Standard alumina (92-95% Al₂O₃) has excellent hardness - Mohs 9 - but it is brittle. Drop a heavy rock on a standard alumina tile, and it will crack. The zirconia particles in a ZTA ceramic liner do something unusual. When a crack begins to form, the zirconia expands slightly and puts the crack tip into compression. The crack stops growing . This gives a ZTA ceramic liner roughly 50% higher fracture toughness than standard alumina, while retaining the same high hardness .
A ZTA ceramic liner also handles sudden temperature changes better. In a cement clinker chute or a steel mill sinter line, temperatures can swing from ambient to several hundred degrees in minutes. Standard alumina tiles can crack from thermal shock. A ZTA ceramic liner withstands those swings .
The trade-off is cost. A ZTA ceramic liner costs more than a standard alumina tile. But in high-impact applications, the longer service life more than justifies the premium. For a wholesale buyer, that means offering a premium product for the most demanding customers, at a premium price.
How They Are Made
The raw material is a blend of high-purity alumina powder (about 75-85%) and zirconia powder (about 15-25%). The two powders are milled together to a very fine, uniform particle size, then spray-dried. Forming is done by dry pressing for smaller tiles and by cold isostatic pressing for larger ones. Isostatic pressing applies uniform pressure from all directions, producing a green tile with consistent density throughout.
After pressing, the tile is dried slowly. Rushing the drying creates micro-cracks. Those cracks are invisible at first, but they grow under impact. The tile is then sintered in a high-temperature kiln at 1500-1600°C. At that temperature, the alumina and zirconia grains fuse together into a dense, pore-free composite structure. Bulk density reaches about 4.0-4.3 g/cm³. Hardness reaches HRA 90, equivalent to Mohs 9.
Quality control includes chemical analysis (X-ray fluorescence), hardness testing, and dimensional checks. Tiles that are chipped, cracked, or out of tolerance are rejected. Out-of-spec tiles do not leave the factory.

Why Customers Benefit
In a gold and copper mine in Western Australia, a customer was using 92% alumina liners in a flash float floor. Those liners lasted about 26 weeks - two shutdown cycles. The customer needed longer life. Bradken supplied ZTA ceramic liners. After 50 weeks, the ZTA liners still had more than 50% of their service life remaining. Projected total life reached 100 weeks - a 285% increase .
In an iron ore mine in Australia, a transfer chute was processing 12,000 tonnes per hour, with material dropping 3 metres. 92% alumina tiles holed after only 7 weeks. The steel backing plate had worn through. Custom ZTA ceramic liners were designed. After 24 weeks, maximum wear was 32 mm, with 18 mm of ceramic remaining. Forecast service life reached 28 weeks - four times longer than the previous lining.
In a Chinese mine slurry system, metal elbows and cones lasted less than six months. ZTA ceramic-lined elbows were installed. After nearly four years of operation, the ceramic still showed more than 80% surface integrity - an eight-fold increase over the original metal parts.
In a steel mill sinter plant, ordinary 92% alumina chute liners cracked within weeks from thermal cycling and impact. ZTA tiles were installed. The mill has run for over two years with no visible cracking.
A ZTA ceramic liner works where ordinary alumina fails. When the customer has heavy impact, thermal shock, or both, ZTA is the right answer.
Ordering
Tecera supplies ZTA ceramic liners in thicknesses from 6 mm to 50 mm, in plain, trapezoid, hexagon, and custom shapes. Over 3,000 standard tile sizes are available. Free samples for destructive testing are available. Lead time for standard sizes is two to three weeks. Custom shapes require four to six weeks. Global shipping with export-grade packaging is provided. Response time for quote requests is typically two business days.
Hot Tags: zta ceramic liner, China zta ceramic liner manufacturers, suppliers, factory, Ceramic Lining Panels for Belt Conveyors
You Might Also Like
Send Inquiry








