Ceramic Transfer Point Tile Liner

Ceramic Transfer Point Tile Liner

Ceramic Transfer Point Tile Liner is a composite wear lining for transfer areas where bulk material creates concentrated impact and abrasive flow. Alumina ceramic tiles form the working surface, supported by a backing layer selected for the mounting condition.
Send Inquiry
Product Introduction

Ceramic Transfer Point Tile Liner is a composite wear lining for transfer areas where bulk material creates concentrated impact and abrasive flow. Alumina ceramic tiles form the working surface, supported by a backing layer selected for the mounting condition. The tile format suits transfer chutes, loading points, hoppers and material transfer zones with defined wear paths.

 

Product Construction

 

Alumina Ceramic Layer
The working layer uses alumina ceramic grades from 92% to 99% Al₂O₃. Ceramic grade and thickness are selected according to material characteristics, impact intensity and abrasive contact.


Composite Backing
Rubber, polyurethane or rigid backing can be combined with the ceramic layer according to the equipment structure and fixing method. The backing supports the tiles and follows the requirements of the mounting surface.

 

Where It Fits

Transfer Chutes

Suitable for chute sections where material falls, changes direction and moves across the lining surface.

Loading Zones

Used at concentrated impact areas below material discharge points and transfer locations.

Hoppers and Bins

Applied to internal surfaces exposed to repeated contact from abrasive bulk materials during loading and discharge.

 

Key Selection Factors

 

Material Characteristics: Particle size, material hardness, density and moisture affect the balance between impact and sliding abrasion.


Drop Height: Material drop height indicates the impact load at the receiving surface and helps determine ceramic thickness and backing construction.


Liner Geometry: Flat, curved and irregular sections require different tile layouts. Dimensions should follow the equipment drawing and actual wear zone.

 

Product Advantages

 

Dense Alumina Surface: Alumina ceramic provides a hard working surface for abrasive material flow, with grades available from 92% to 99% Al₂O₃.


Composite Structure: The ceramic layer provides the wear surface while the backing provides structural support suited to the mounting condition.


Modular Tile Layout: Individual tiles can be arranged around corners, transitions and concentrated wear areas to follow the equipment profile.


Controlled Thickness: Ceramic thickness can be selected within the available range according to wear allowance, impact conditions and installation space.

 

Technical Parameters

 

Parameter

Typical Value

Alumina content

≥92–99% Al₂O₃

Bulk density

≥3.63–3.83 g/cm³

Water absorption

≤0.01%

Mohs hardness

9

Fracture toughness

4.60–5.50 MPa·m¹/²

Flexural strength

≥240–300 MPa

Ceramic thickness

6–50 mm

Tile size range

50 × 50–300 × 300 mm

 

Material Selection

01/

92% Alumina
Suitable for general abrasive transfer areas where a standard alumina ceramic grade meets the operating condition.

02/

95% Alumina
Used where increased alumina content and ceramic density are required for more demanding abrasive service.

03/

97–99% Alumina
Selected for applications requiring higher alumina content and density within the available ceramic grade range.

04/

Backing Material
Rubber, polyurethane or rigid backing can be selected according to impact load, liner shape and fixing requirements.

Impact Condition Assessment

 

Drop Point
Locate the first material contact point. This area normally receives the highest concentrated impact.
Particle Size
Coarse particles create localized impact, while finer material can generate broader sliding abrasion.
Flow Direction
Material trajectory should be mapped from the entry point through the transfer zone to identify changes in impact and sliding conditions.

 

Wear Zone Planning

 

Primary Impact Area
Ceramic thickness and backing support should reflect the concentrated load at the initial impact location.
Sliding Area
Ceramic grade and thickness should correspond to the duration and intensity of abrasive material contact.
Transition Area
Tile arrangement should follow changes in material direction and maintain continuous wear coverage across the transition.

 

Installation Considerations

 

Surface Preparation
The mounting surface should be clean, stable and prepared for the selected fixing system.
Tile Layout
Tile dimensions and joint arrangement should follow the equipment profile and material flow path.
Maintenance Access
Modular sections should allow access to defined wear areas during inspection and scheduled maintenance.

 

Suitable Industries

 

Mining and Mineral Processing
Used in transfer chutes, hoppers and loading areas handling abrasive ores and mineral materials.
Cement and Aggregates
Applied to material transfer sections exposed to clinker, limestone, aggregate and other abrasive solids.
Power and Bulk Handling
Suitable for internal wear zones handling coal, ash, minerals and other bulk materials.

 

Quality Control Points

 

Ceramic Properties: Alumina content, density, hardness, water absorption and flexural strength should conform to the specified ceramic grade.


Dimensional Control: Tile length, width and thickness should be checked against approved drawings and agreed tolerances.


Surface Inspection: Finished tiles should be inspected for visible cracks, edge damage and dimensional conformity before assembly or shipment.

 

Specification for Quotation

 

Provide the liner dimensions, equipment drawing, material type, particle size, approximate drop height, flow direction, operating temperature and installation method. Photos of the existing wear area can help identify the wear pattern and define the ceramic grade, thickness, tile layout and backing construction.

 

Frequently Asked Questions

 

Q: What is a Ceramic Transfer Point Tile Liner?

A: It is a composite wear lining with an alumina ceramic working surface for transfer areas exposed to impact and abrasive bulk material flow.

Q: What alumina grades are available?

A: Available ceramic grades range from 92% to 99% Al₂O₃. Grade selection depends on material characteristics and operating conditions.

Q: What ceramic thicknesses are available?

A: Ceramic thicknesses generally range from 6 to 50 mm, with thickness selected according to wear conditions, impact load and available installation space.

Q: Can tile dimensions be customized?

A: Yes. Tile dimensions, shapes, thicknesses and layout can be specified according to the equipment profile and approved drawing.

Q: What information is required for selection?

A: Key information includes material type, particle size, drop height, flow direction, operating temperature, liner dimensions and fixing method.

Q: Can different ceramic grades be used within one transfer point?

A: Yes. Different wear zones can use different ceramic grades or thicknesses when impact and abrasion conditions vary across the equipment.

Hot Tags: ceramic transfer point tile liner, China ceramic transfer point tile liner manufacturers, suppliers, factory

Send Inquiry

Home

Phone

E-mail

Inquiry