Alumina Ceramic Tile Liner

Alumina Ceramic Tile Liner

An alumina ceramic tile liner is a precision‑shaped wear plate bonded to chutes, hoppers, and pipes in mining, coal, and cement plants. It solves rapid steel erosion by providing a hard, impact‑resistant surface that outlasts metal liners by years – reducing emergency shutdowns and cutting maintenance costs for bulk material handling.
Send Inquiry
Product Introduction
 

A chute made of steel lasts a few months in a coal prep plant. A hopper made of rubber tears after a single winter. A pipe carrying fly ash erodes from the inside in weeks. Tecera's alumina ceramic tile liner is the fix. You bond these tiles to the inside of your equipment – chutes, hoppers, bins, pipes, cyclones – and the ceramic takes the punishment instead of the steel.

 

The core advantage is not just longer life, but predictable life. A steel liner fails when it fails. A ceramic liner wears slowly, evenly, and you can see it coming.

 

For a plant manager, that means scheduled maintenance instead of emergency calls at 2 AM.

interlock ceramic cube liner
 
 
 

Material and Manufacturing

Material and Manufacturing

Choose the plan that suits you best.

calcined alumina powder

For 92% and 95% grades, the powder is domestic. For 97% and 99%, it is imported to keep iron and sodium very low – because in some applications, even trace metal contamination is a problem.

01

uniform particle size

Spray‑dried into free‑flowing granules. Forming is done by dry pressing for smaller tiles and by cold isostatic pressing (CIP) for larger ones. CIP applies pressure from all directions, so the tile has the same density at its centre as at its surface. 

02

dried slowly

Rush this step and you get micro‑cracks – invisible but fatal. The dried tiles are sintered at 1500–1550 °C in a tunnel kiln. At that temperature, the alumina grains fuse. Bulk density reaches 3.63–3.85 g/cm³, and water absorption drops below 0.01%.

03

Quality control

Chemical composition is verified by XRF. Hardness is tested with a Vickers indenter. Dimensional accuracy is checked with calibrated gauges. Tiles that are chipped, cracked, or out of tolerance are rejected. Roughly 2–3% of production never leaves the factory.

04

Technical Data

 

The table below shows typical values for Tecera's tile grades. Batch certificates are available.

Grade

Al₂O₃ (%) Bulk Density (g/cm³) Water Absorption (%) Mohs Hardness Fracture Toughness (MPa·m¹/²) Flexural Strength (MPa)
TW92 ≥92 ≥3.63 ≤0.01 9 4.60 ≥240
TW92S ≥92 ≥3.63 ≤0.01 9 5.70 ≥255
TW95 ≥95 ≥3.68 ≤0.01 9 4.65 ≥250
TW95S ≥95 ≥3.68 ≤0.01 9 4.70 ≥270
TW97 ≥97 ≥3.73 ≤0.01 9 5.20 ≥285
TW99 ≥99 ≥3.83 ≤0.01 9 5.50 ≥300

Application Industries

 

Mining

Chutes, hoppers, transfer points, cyclone feeders. A copper mine in Chile installed TW95 tiles in a primary crusher discharge chute. The previous steel chute lasted six months; the tiles have run for three years.

Mining

Coal preparation

Raw coal hoppers, magnetite medium chutes, dense medium cyclones. A prep plant in West Virginia used interlocking trapezoid tiles in a vibrating feeder. Four winters, no failures.

Coal preparation

Cement

Clinker chutes, raw meal bins, mill discharge pipes. A cement plant in Brazil replaced steel liners every eight months with TW92S tiles. The tiles lasted 28 months.

Cement

Steel

Sinter plant chutes, pelletizing disc liners, coke handling hoppers. High temperature plus abrasive sinter feed. TW95S tiles handle both.

steel

Power generation

Coal pulverizer feed chutes, ash hoppers, limestone slurry lines. A power plant in Ohio installed TW95 tiles in a fly ash elbow. The steel elbow lasted six months; the ceramic has been in service for over five years.

Power generation

 

Product Advantages

Why This Tile Works for Your Customers
 
 
 

No liquid penetration

Sintering at 1500°C closes the pores. Water absorption stays below 0.01%. In a coal plant, acidic slurry won't soak in. In a freezing climate, moisture won't get trapped and crack the tile. Your customer avoids two common failures. You get a product you can sell anywhere.

 
 

Trapezoid interlocking

Square tiles rely on epoxy alone. Vibration loosens them. Trapezoid tiles wedge against each other. Even if the adhesive ages, they stay put. No loose tiles means no jammed crushers, no clogged chutes. Fewer warranty claims for you.

 
 

High fracture toughness

TW92S and TW95S grades have toughness of 5.70 and 4.70 – higher than standard alumina. In a crusher chute where rocks drop from height, standard tiles crack in weeks. These last years. For a mine doing 10,000 tons a day, avoiding a four‑hour shutdown saves tens of thousands. You can charge more for the tougher grade.

 
 

Hardness stops

scratching

Alumina is Mohs 9. Steel is 5–6. Quartz is 7. Quartz cuts steel. It does not cut alumina. A steel chute in a cement plant lasts six months. Tecera tiles last three to five years. Your customer saves money. You get repeat orders.

 

 

Ordering

Tecera supplies alumina ceramic tile liners in all TW grades, with over 3000 standard sizes and full customization. Bulk pricing, free samples for destructive testing, and global shipping are available.

To request a quote, provide: tile dimensions and thickness, grade required, material being handled, and estimated annual volume. For custom shapes, send a drawing in DWG, PDF, or STEP format. We respond within two business days.

Contact now

 

 

 

 

 

 

Hot Tags: alumina ceramic tile liner, China alumina ceramic tile liner manufacturers, suppliers, factory, ceramic liner

Send Inquiry

Home

Phone

E-mail

Inquiry